How to Measure the Loss in the APC Connector? | www.flukenetworks.com

Blog

Voltar para todos os blogs

How to Measure the Loss in the APC Connector?

Barry Lindsley

This question often gets asked in my classes at the same time as when talking about launch methods using launch and tail fibers. So let’s talk about launch fiber compensation.

Launch Methods in OTDR Machines

Launch fiber compensation: When we make an OTDR (Optical Time Domain Reflectometry) measurement, we use the launch cable to allow the trace to settle down after the pulse(s) are sent into the fiber, allowing us to see and analyse the start of the fiber being tested. This is because a large event will be seen in front of the connection on the trace usually caused by reflectance from the connector on the OTDR, thus not allowing us to make a good measurement of the first connection. The launch fiber also overcomes the issue of any dead zone (unseen event) that may occur if the pulse width is wider than the distance to a connector a short distance away from the OTDR connector.

An additional a short fiber cord may be added in between the OTDR and the launch fiber, usually called a “sacrificial cord” as it will sacrifice its connector rather than connector on the launch fiber.

A launch fiber is typically used in-conjunction with a tail fiber. This allows the end of the measured fiber link to be measured. If a tail fiber is not used we are not able measure or analyse the end connector.

Launch methods: On Fluke Networks OptiFiber Pro there are four different methods that can be made using launch and tail fibers.

OptiFiber Pro with Angle Polish Connector
OptiFiber Pro without Angle Polish Connector
 

Launch only compensation: Where the length and loss of the launch fiber is removed from the results. However, this will result in the far end not being able to be analysed. To overcome this, the fiber should also be measured from the other end. If you use this compensation method you will not be able to do bi-directional averaging.

Launch and tail compensation: Where the length and loss of the launch and tail fibers are removed from the measurement. This method allows the far end connector as well as the near end connector of the fiber link to be evaluated. Another advantage of this method is it allows a fiber link to be evaluated even if the launch and tail fibers are different from the link under test or there are a number of different fibers within the link under test. This method is required to be used if bi-directional averaging is required.

Launch, fiber and tail compensation: Where the length and loss of the launch and tail fibers are removed from the measurement. This method has the advantage of allowing you to do the compensation with a connected link included. However, the disadvantage is you cannot access your launch fibers.

Manual compensation: This method of compensation removes the length and loss of the launch and tail fibers, but the cord lengths of both the launch and tail fibers are required to be entered manually on the OptiFiber Pro. This guarantees that the OptiFiber Pro knows where the first and last connectors are located in the link even if they have no measurable loss or reflectance.

Warning Screen for Tail Event Not Found

This brings us back to the original question. When we make an OTDR measurement on a link that has an APC (Angled Physical Contact connector or sometimes called Angle Polish Connector) at the end of a link, it’s possible that the OTDR will not see the end of the link because the APC has no measurable reflectance or loss. To overcome this, the manual compensation method should be deployed on the OptiFiber Pro.

If we simply use the launch and tail compensation method, not manual compensation as mentioned, we may not have any measurable reflectance or loss at the end of the link. In this situation, the OptiFiber Pro produces the warning screen on the right.

 

Warning Screen for Launch and Tail Event Not Found

If we use the suggested manual compensation method, the OptiFiber Pro knows where the first and last connectors are in the link because we programmed in the length of the launch and tail fibers. When an OTDR measurement is made and no reflectance or loss is measured at the start or the end of the link, a virtual event will be marked on the trace. In addition this screen will be produced.

I hope this short article has helped you understand how an OTDR can test a link with an APC connector in the link and understand the different methods of launch compensation.

 

 

 

 

 

 

Barry LindsleyBarry Lindsley possui 44 anos de experiência no setor de testes e medição, trabalhando para a Tektronix, Fluke e Fluke Networks. Ele trabalha há 23 anos no setor de redes. Durante este período, ele ocupou cargos técnicos e outros cargos técnicos aliados a marketing. Ele também liderou o grupo TIA (Reino Unido) Sig 11 que trabalhou nos testes CAT5E. Nos últimos 3 anos, Barry tem uma empresa de consultoria que presta serviços técnicos profissionais para redes e marketing.

 


 
 
Powered By OneLink